Hydrotek AR pump replacement
- Thread starter Osoto
- Start date
Russ Johnson
Equipment Expert
Marty, call me later today. I'll look it up for you and price you a new one.
Mark
New member
Marty,
Most likely it is an RK15.28 pump.
Does it look like this pump in the breakdown:
http://arnorthamerica.com/newbreakdowns/Pumps/rk_1450.pdf
The RK15.28 is used on both 4 GPM @ 4000 PSI units 1450 RPM,
as well as 4.8 GPM @ 3000 PSI 1750 RPM.....
Now might be a good time to consider upgrading pump,
either to a TS2021 General or an AR XWM2128.
You can upgrade engine at another time but already
have a higher volume pump. Use Hydro Tek pump rails,
Russ should be able to sell you any of this.
http://arnorthamerica.com/xwseriespumps.html
If it were me I would go with the XWM2128 now
(with Hydro Tek pump rails) and later a 21 HP Vanguard)
Then with the addition of a new unloader you have 5.5 GPM @ 4000 PSI !
I see you have Moore in your signature...... JHow is the recovery coming along?
Just thought I would mention that Hydro Tek and Alkota matched our $100 donation
for every machine sold between 5/24/2013 and July 1, 2013..
Here is a link :http://www.powerwashnetwork.com/shoot-bull/12271-how-help-oklahoma-tornado-victims.html
http://www.easycleansystems.com/PDF_Folder/Buy%20Now%20Help%20Moore.pdf
Rest assured with Hydro Tek you have a great pressure washer, and although I have never personally met
Russ I can say he has an excellent reputation.
Most likely it is an RK15.28 pump.
Does it look like this pump in the breakdown:
http://arnorthamerica.com/newbreakdowns/Pumps/rk_1450.pdf
The RK15.28 is used on both 4 GPM @ 4000 PSI units 1450 RPM,
as well as 4.8 GPM @ 3000 PSI 1750 RPM.....
Now might be a good time to consider upgrading pump,
either to a TS2021 General or an AR XWM2128.
You can upgrade engine at another time but already
have a higher volume pump. Use Hydro Tek pump rails,
Russ should be able to sell you any of this.
http://arnorthamerica.com/xwseriespumps.html
If it were me I would go with the XWM2128 now
(with Hydro Tek pump rails) and later a 21 HP Vanguard)
Then with the addition of a new unloader you have 5.5 GPM @ 4000 PSI !
I see you have Moore in your signature...... JHow is the recovery coming along?
Just thought I would mention that Hydro Tek and Alkota matched our $100 donation
for every machine sold between 5/24/2013 and July 1, 2013..
Here is a link :http://www.powerwashnetwork.com/shoot-bull/12271-how-help-oklahoma-tornado-victims.html
http://www.easycleansystems.com/PDF_Folder/Buy%20Now%20Help%20Moore.pdf
Rest assured with Hydro Tek you have a great pressure washer, and although I have never personally met
Russ I can say he has an excellent reputation.
I bought this about 3 years ago for $200. Apparently the shelled the pump and was clueless. It sat for a while. The fuel pump was leaking. Poured some gas in the carb, hooked it to a motorcycle battery, started right up. It's great to be mechanicaly inclined. Junk becomes treasure!
Thanks, but I actually found a pump a similar pump in my garage. As this project progresses you'll be getting some calls. I can tell there's more parts I'll be needing.
These are some great ideas. The PDF didn't show. If I find another basket case I'm definately going this route.
Storm recovery seems to be going well. My house was unaffected, but my wife's shop lost her roof. That turned out to be a good thing. Complete remodel for her.
Thank you guys for the replies and good advise.
innovativewash
New member
I have this pump sitting on a shelf in my shop. I can see how much it would be to ship if I can get your address. $125 bucks for the pump. plus shipping.
Did you make a Sale? lol