Russ Spence
Commercial Pressure Wash Expert
Cleanpeers Home Page
Roof Cleaning --Asphalt Shingles
By Henry Bockman
Roof cleaning of asphalt shingle roofs are a fairly new niche market that many pressure washing companies have started to notice. The process of cleaning asphalt shingle roofs is fairly simple if you educate yourself on how roofs are installed, possible problems and situations to avoid and what type of stains you need to remove.
Most pressure washing companies that begin roof cleaning find that there is a considerable amount of technique and skill when cleaning roofs. Any contractor that performs roof cleaning should be aware of roofs are installed, failure to understand roof installation methods can cause thousands of dollars in damages from a pressure washing contractor.
Its imperative that the pressure washer use extremely low pressure to avoid damaging the shingles and that the roof is inspected prior to the commencement of the job. Remember, most pressure washers used in roof cleaning use a minimum of 4 GPM and as much as 10 GPM!. So it is easy to understand why knowledge of roofing installation and a roof inspection is necessary when you consider the amount of water that could enter the structure during roof cleaning.
Now that you understand the basicsof roof installation it is equally important to know the other structures on the roof and their function to avoid causing leaks around them. For identification purposes, pictures of these parts can be found on the roofing page of our web site at http://www.henryshousework.com/HHW/roof_repair.html Most roofing materials are installed over a layer of felt paper and in some cases a rubber like ice guard material. The first layer of shingles is called the starter course and is installed at the lowest point on the roof, upside down. This allows a solid base for water to run over without leaking down into the rafters and plywood between the shingles key ways. Once this layer is installed another shingle is place directly on top of it, and the rest of the roofing is placed in a similar fashion up the roof line. The reason shingles are installed in this manner is to allow the water to run over one shingle onto the next until it enters the gutter system.
Now that you can identify the common fixtures on a roof the next step is to identify what you will be cleaning from the surface. The most common reason for cleaning asphalt shingle roofs is to remove a fungus growth called Gloeocapsa Magma. This particular type of algae is air-born and will collect on any type of roof. In most cases the owner of the property won't notice the algae growth until it begins to take over large sections of the roof. This algae usually forms dark brown or black stains on the roofing and it thrives in mostly warm humid areas.
Roof cleaning with the appropriate cleaners can effectively remove this unsightly blemish from roofs fairly easily if you know how. Some manufacturers suggest using a mixture of TSP and Bleach to kill the fungus. Other manufacturers suggest using a sodium hydroxide based cleaner instead.
Regardless of which cleaner you use when cleaning roofs it's important that you check with the manufacturer of the roof to meet their guidelines. Some manufacturers will void the warranty on the shingles for one method but not the other. However, ALL roofing manufacturers agree that the use of high pressure should NEVER be used when cleaning roofs. Some specifications set the safe pressure range at 600 PSI but the best rule of thumb to use is. Use the least amount of pressure and the mildest chemical possible to achieve the desired result!
If you are considering entering the asphalt shingle roof cleaning market I would highly recommend taking a course offered by The Power Washers of North America. This informative course will give you an in depth look at proper techniques, chemical processes, and roof construction needed to add this valuable service to your company.
Author Bio:
Henry Bockman, operates Henry's Housework (http://www.henryshousework.com) a pressure washing company in Maryland, holds Environmental and Wood certifications from the Power Washers of North America, Wolman, American Builders and Restoration and other contractor organizations. Bockman also instructs for some of the PWNA training and certification courses. (http://www.pwna.org) He also recommends using professional pressure washing products from suppliers like Sun Brite Supply of Maryland (http://www.sunbritesupplymd.com) instead of using high pressure to clean.
anyone have oponions on this ??????
i dont see anyone using sodium hydroxide on shingles nor have i ever seen it "approved" anywhere by any roofing manufacturer ......... comments???????
if you have seen a asphalt roofing manufacturer "approve" the use of a sodium hydroxide based cleaner i would like to see the link
i dont want to badgerhenry and i am not trying to but i would like tosee proof of the above
Roof Cleaning --Asphalt Shingles
By Henry Bockman
Roof cleaning of asphalt shingle roofs are a fairly new niche market that many pressure washing companies have started to notice. The process of cleaning asphalt shingle roofs is fairly simple if you educate yourself on how roofs are installed, possible problems and situations to avoid and what type of stains you need to remove.
Most pressure washing companies that begin roof cleaning find that there is a considerable amount of technique and skill when cleaning roofs. Any contractor that performs roof cleaning should be aware of roofs are installed, failure to understand roof installation methods can cause thousands of dollars in damages from a pressure washing contractor.
Its imperative that the pressure washer use extremely low pressure to avoid damaging the shingles and that the roof is inspected prior to the commencement of the job. Remember, most pressure washers used in roof cleaning use a minimum of 4 GPM and as much as 10 GPM!. So it is easy to understand why knowledge of roofing installation and a roof inspection is necessary when you consider the amount of water that could enter the structure during roof cleaning.
Now that you understand the basicsof roof installation it is equally important to know the other structures on the roof and their function to avoid causing leaks around them. For identification purposes, pictures of these parts can be found on the roofing page of our web site at http://www.henryshousework.com/HHW/roof_repair.html Most roofing materials are installed over a layer of felt paper and in some cases a rubber like ice guard material. The first layer of shingles is called the starter course and is installed at the lowest point on the roof, upside down. This allows a solid base for water to run over without leaking down into the rafters and plywood between the shingles key ways. Once this layer is installed another shingle is place directly on top of it, and the rest of the roofing is placed in a similar fashion up the roof line. The reason shingles are installed in this manner is to allow the water to run over one shingle onto the next until it enters the gutter system.
Now that you can identify the common fixtures on a roof the next step is to identify what you will be cleaning from the surface. The most common reason for cleaning asphalt shingle roofs is to remove a fungus growth called Gloeocapsa Magma. This particular type of algae is air-born and will collect on any type of roof. In most cases the owner of the property won't notice the algae growth until it begins to take over large sections of the roof. This algae usually forms dark brown or black stains on the roofing and it thrives in mostly warm humid areas.
Roof cleaning with the appropriate cleaners can effectively remove this unsightly blemish from roofs fairly easily if you know how. Some manufacturers suggest using a mixture of TSP and Bleach to kill the fungus. Other manufacturers suggest using a sodium hydroxide based cleaner instead.
Regardless of which cleaner you use when cleaning roofs it's important that you check with the manufacturer of the roof to meet their guidelines. Some manufacturers will void the warranty on the shingles for one method but not the other. However, ALL roofing manufacturers agree that the use of high pressure should NEVER be used when cleaning roofs. Some specifications set the safe pressure range at 600 PSI but the best rule of thumb to use is. Use the least amount of pressure and the mildest chemical possible to achieve the desired result!
If you are considering entering the asphalt shingle roof cleaning market I would highly recommend taking a course offered by The Power Washers of North America. This informative course will give you an in depth look at proper techniques, chemical processes, and roof construction needed to add this valuable service to your company.
Author Bio:
Henry Bockman, operates Henry's Housework (http://www.henryshousework.com) a pressure washing company in Maryland, holds Environmental and Wood certifications from the Power Washers of North America, Wolman, American Builders and Restoration and other contractor organizations. Bockman also instructs for some of the PWNA training and certification courses. (http://www.pwna.org) He also recommends using professional pressure washing products from suppliers like Sun Brite Supply of Maryland (http://www.sunbritesupplymd.com) instead of using high pressure to clean.
anyone have oponions on this ??????
i dont see anyone using sodium hydroxide on shingles nor have i ever seen it "approved" anywhere by any roofing manufacturer ......... comments???????
if you have seen a asphalt roofing manufacturer "approve" the use of a sodium hydroxide based cleaner i would like to see the link
i dont want to badgerhenry and i am not trying to but i would like tosee proof of the above
